One for All Universal Remote UR2 DTA User Manual

IMPORTANT SETUP NOTE!  
STEP4 After you’ve entered the correct  
code number and the Component  
has turned Off, press the [POWER]  
button to turn the Component  
back On. Now it is time to test the  
VOLUME and MUTE buttons for  
the TV to make sure they all work.  
If any of the functions do not work  
as they should, repeat from STEP  
3 using the next 3-digit code num-  
ber listed for that brand until you  
find the best code.  
Now, repeat the Auto-Search Method If you wish to store the TV volume  
Introduction  
Button Functions  
4
1
Operating Instructions For  
control in DTA mode, use the follow-  
ing steps.  
for those Components you could  
not program earlier with the Pre-  
Programmed Method.  
This pertains to all programming steps.  
When you are in setup mode, a compo-  
nent LED will light for 20 seconds.If you do  
not press a button within 20 seconds, the  
LED light will turn off and exit setup mode  
and you will need to start over.  
The UR2-DTA is designed to  
operate the S/A, Pace Micro,  
Motorola and IPTV set tops, plus  
the majority of TV equipment on  
the market as shown below.  
STEP1 Press the [DTA] button and  
the [OK] button simultane-  
ously for 3 seconds.  
UR2-DTA  
D. Finding a Component Button’s  
Setup Code Number  
DTA Remote Control  
The [DTA] Component LED  
will turn on for 20 seconds.  
DTA : DTA boxs, IPTV set tops  
TV : Televisions  
If you used the Auto-Search Method  
to program a Component, you may  
not know what the correct code num-  
ber is. Here is a way for you to identi-  
fy the code number, so you can  
record it for future reference.  
A. Quick Set-Up Method  
STEP2 Press the [VOL ] button.  
STEP1 Turn on the device you want to  
program-to program your TV,  
turn the TV on.  
STEP3 Press the [TV] button.  
The Component LED will  
blink twice to confirm the  
programming.  
Replacing Batteries  
Before you program or operate the  
remote control, you must install two new  
AA alkaline batteries.  
2
STEP5 Once you have found the correct  
3-digit code, save it by pressing  
the same [COMPONENT] button  
one more time. The POWER LED  
light will blink twice to confirm that  
the code was successfully stored.  
STEP2 Point the remote at the TV and  
press and hold TV key for 3 sec-  
onds. While Holding the TV key,  
the POWER LED will light off and  
on again. Begin to press the  
number keys, one at a time,  
starting with 1, then 2, 3...0 until  
the TV turns off.  
To return to original state:  
STEP1 Press the [COMPONENT] but-  
ton (TV or DTA) you want to  
verify and the OK button simul-  
taneously for 3 seconds. The  
POWER LED light will turn on  
for 20 seconds.  
If you wish to restore the DTA volume  
control in DTA mode, repeat the  
above steps but press [DTA] in  
STEP1 Remove the battery compart-  
ment cover on the back of your  
remote control.  
STEP3 .  
C. Auto-Search Method  
STEP1 Turn on the Component you  
STEP2 Check battery polarity carefully,  
and install the batteries as  
shown in the illustration below.  
F. Memory Lock System  
STEP2 Press the [INFO] button and  
count the number of times the  
Component LED light blinks.  
This number indicates the first  
digit of the code, followed by  
the second and third, each sep-  
arated by a one second pause  
when the LED will turn off.  
STEP3 Release the TV key to save the  
code. The POWER LED will blink  
twice to confirm the code is  
stored.  
want to program (TV, DTA).  
This remote control is designed to  
retain programmed memory for 10  
years even after batteries are  
removed from the remote control.  
STEP2 Press the [COMPONENT] button  
(TV or DTA) to be programmed  
and OK button simultaneously  
for 3 seconds. The POWER LED  
light will turn on for 20 seconds  
indicating the unit is ready to be  
programmed.  
STEP3 Replace the battery compart-  
ment cover.  
B. Pre-Programmed 3-Digit Code  
Method  
G. Write your TV Set-up codes  
Set-up Code Number :  
STEP1 Turn on the Component you want  
For additional information about your  
remote.com  
to program(TV, DTA).  
*Note : 10 blinks represents the  
STEP3 Point the remote toward the  
Component and press the [CH]  
or [CH] button one step at a  
time or keep it pressed. The  
remote will emit a series of  
ON/OFF commands. Release the  
[CH] or [CH] button as soon  
as the Component turns Off.  
number zero.  
STEP2 Press the [COMPONENT] button  
(TV or DTA) to be programmed  
and OK button simultaneously  
for 3 seconds. The POWER LED  
light will turn on for 20 seconds  
indicating the unit is ready to be  
programmed.  
Example : One blink, (pause), eight  
blinks, (pause) and three  
blinks, indicates code  
number 183.  
Programming the Remote Control  
5
There are three ways you can program your remote:  
* Quick Set-Up Method  
E. Programming Volume Control  
* The Pre-Programmed 3-Digit Code Method  
* The Auto-Search Method  
STEP4 Test functions. (Same as for 3-  
Digit Code Programming Method  
- Section B). If any of the func-  
tions do not work as they should,  
repeat from STEP 3 using [CH]  
or [CH] buttons to find the cor-  
rect code.  
STEP3 Point the remote control toward  
the Component and enter the 3-  
digit code number assigned to  
your brand.  
Volume and Mute control are factory-  
programmed to automatically transfer  
to the respective Component mode you  
select, as follows:  
Operations  
3
The Quick Set-Up Method is a unique new feature that enables the fastest and  
easiest set-up by using one-digit codes for up to 10 major brands for each compo-  
nent.  
Volume Default: TV volume and mute  
through The TV, with the option of con-  
trolling volume and mute through the  
Cable. Refer to Section E For program-  
ming the volume and mute through  
your Cable.  
*Note : If the 3-digit code number you just  
entered is correct, the Component  
will turn Off. If it did not turn Off,  
continue entering code numbers  
listed for that brand until the  
Component turns Off.  
DTA : TV T V : TV  
The Pre-Programmed Code Method allows you to setup all the buttons at once by  
entering 3-digit code numbers that correspond to a particular Component’s manu-  
facturer/brand, so it’s the fastest and easiest of the two methods. (Code Tables  
are on the backside of this Instruction Sheet.) The Auto-Search Method scans  
through all the codes in the remote control, one at a time.  
However, you can program the volume  
controls (Volume Up, Volume Down  
and Mute) from one Component to  
operate in another Component.  
STEP5 Save the code. (Same as for  
3-Digit Code Programming  
Method - Section B).  
Universal Remote Control, Inc.  
OCE-0089A REV 03 (05/26/10)  
 

Miele Saw B 895 D User Manual
Miele Washer W 1966 User Manual
Moxa Technologies Surge Protector A51 User Manual
Mr Handsfree Headphones Blue Bird User Manual
MTD Blower 24695 8 User Manual
Northern Industrial Tools Impact Driver 1981202 User Manual
Oki All in One Printer 18 24DXE 2 User Manual
Onkyo DVD Player DV BD507 User Manual
Oreck Vacuum Cleaner U4080H2 User Manual
Panasonic Printer EPL1700 User Manual